PI / MATRIX STAND — CASE TRAY REVISION 7

Use print-files-v7/. Import STLs in millimeters at 100%, without resizing.
This replaces v6: full-width sloped gussets support the diffuser shelves;
the camera pad now has a flat front web and lower crossbar, so it prints
front-face-down in one connected first layer. Use the NEW v7 camera pad.
The fit gauges, case tray size, hinge bolt and diffuser slot are unchanged.

CASED PI TRAY
Sized for the supplied external case dimensions: 94 x 63 x 45 mm.
Assumed orientation: 94 mm left-right, 63 mm front-back, 45 mm tall.
Clear tray opening: 98 x 67 mm (2 mm clearance per side).
Two broad rails lift the case bottom to 6 mm above the base bottom,
2 mm above the vented floor. No PCB standoffs or mounting screw holes.
Corner rims rise to 12 mm above the base bottom, 6 mm above the seat.
Edges between the corners stay open for connectors and cables. Check real
port locations, feet, lid shape and bottom vents; only an outer case box is
modeled. The placeholder does not represent the exact CanaKit case model.
The case front is 52 mm behind the base front. Remove before carrying;
the rim locates the case but does not lock it in. Optional light cable ties
can use the small slots alongside the case; keep vents and ports unobstructed.

CAMERA AND CABLES
Keep the existing case/ribbon opening toward the camera, if possible.
The camera remains bottom center, on an M3 tilt joint, about +/-25 degrees.
135 mm usable camera cable is the original measured exposed length. Do not
count cable concealed in a connector as free length.
The external connector-route estimate is 66 mm. A 20 mm bend/layout allowance
plus a provisional 15 mm internal-case allowance gives about 101 mm total,
leaving a planned 34 mm. This is NOT a verified cable fit: the actual internal
path and case exit are unmeasured. The orange line is only a schematic route.
Do an unpowered layout with the real case, camera and cables first. Verify a
relaxed loop through the useful tilt range without pinching, sharp bends or
pulling either connector. Adjust the layout if your case needs more cable.
The estimated 279.4 mm matrix ribbon route plus allowance is about 162 mm.
Check the real matrix adapter, external wires and their exits too.

OPTIONAL DIFFUSER
For nominal 3 mm / 1/8 inch (3.175 mm) acrylic, the clear slot is 3.8 mm.
Use a deburred approximately 191 x 191 mm sheet matching the measured panel.
Clear width is 195 mm. Measure before cutting and test a scrap in the gauge.
Slide it down from above, parallel to the 8-degree display. It is gravity
retained; remove it before carrying. The slot can be left empty.
There is at least 6 mm modeled clearance ahead of the illustrative LED face.
Real LED lens protrusion and the optical diffusion result need testing.
Product reference: https://www.amazon.com/dp/B0G4JJSFCS

PRINT AND FIT CHECKS
1. Print panel-fit-gauge-v7.stl: 201 x 32.8 x 9.9 mm, flat on plate.
   Main opening: 195 x 17 mm for the nominal 191 x 191 x 15 mm display.
   Separate front opening: 195 x 3.8 mm for acrylic. Never force either part.
2. Print insert-fit-coupon-v7.stl, supplied orientation.
   Dots mark 4.2 / 4.4 / 4.6 mm trial pilot diameters (1 / 2 / 3 dots).
   Test the M3 insert marked 6*5 (6 mm long, 5 mm outside diameter).
3. Print the full-size layout-check-v7.svg at 100%; verify its 100 mm bar.
   Dry-fit the real case and cables against it before printing the full base.
4. stand-base-v7.stl: 211 x 126 x 110 mm, flat bottom on plate.
   The diffuser shelf gussets reduce unsupported overhangs. Start with removable supports OFF. The small horizontal hinge bores
   have short bridging roofs; check the actual sliced preview and test coupon.
   Check layer preview and clean horizontal holes as needed.
5. camera-tilt-pad-v7.stl: 35 x 46 x 11 mm, supplied FRONT-FACE-DOWN orientation.
   Print as supplied, without reorienting onto its side. Start supports OFF.
   The 3.4 mm horizontal hinge bore is a short bridge; light hole cleanup may
   be needed. A brim is optional adhesion aid, not support material.
Starting settings, not a tested profile: X1C, nonconductive PETG, 0.4 mm nozzle,
0.20 mm layers, 4 walls, 5 top/bottom layers, 15-20% infill.
No G-code or printer profile is supplied. Verify in Bambu Studio.

ASSEMBLY
Disconnect both power supplies before moving hardware or changing cables.
Install a tested M3 6*5 heat-set insert from the outside of the thicker right
fork ear. Nominal pilot: 4.4 mm diameter x 6.4 mm deep. If the test coupon
suggests another size, edit dimensions-v7.json and regenerate before printing.
Let the insert cool, then fit the camera pad using an M3 x 20 mm screw and
two approximately 0.5 mm M3 washers. Do not overtighten the fork.
Tape the camera board at the flat plate side edges with nonconductive foam tape;
leave components, lens and ribbon latch free. Route the ribbon through the
center window and keep it out of the pivot and fan.
Seat the display against its plastic frame edges. Confirm rear braces clear
chips, solder joints and connectors. Optional thin protective pads can be used.
Place the cased Pi on the rails, check vents, cables and fan, then power the
matrix followed by the Pi. All hardware is gravity retained, not transport rated.

VALIDATION
Actual exported STLs reimported: one connected watertight positive-volume solid
per file, each axis under 250 mm. Nominal case, display, diffuser insertion
and camera tilt interference checks pass. The case, vents, wiring, fit,
strength, insert installation and print behavior have not been physically tested.
See mesh-checks-v7.json for the assumptions and numeric checks.

REGENERATE
Edit dimensions-v7.json; run build_stand_v7.py with manifold3d, trimesh,
numpy, networkx and matplotlib. Example environment:
MPLCONFIGDIR=/tmp/pi-stand-matplotlib /tmp/pi-stand-cad-env/bin/python build_stand_v7.py

ONE-PLATE LAYOUT
x1c-one-plate-v7.3mf contains four separate geometry objects on one nominal
X1C plate. No printer or filament profile and no sliced G-code is supplied. The design
target is zero removable supports; that is not a tested print guarantee.
Use print-by-layer, not sequential/by-object. Bounding rectangles leave 5 mm
margin for brim/support footprints; actual generated supports, calibration
lines and machine exclusions still require final slicer preview. Print the
two fit coupons first before committing to the larger final pieces.
