# CLASSIC 04-M2 engineering review

Revision date: November 13, 2026. Engineering review and quotation only.

This revision preserves the selected slim 04-M exterior, rounded camera crown and exposed native controls. It replaces the 04-M1 review candidate for engineering discussion. The thicker 04-N design remains rejected. Supplier portals still contain the earlier 04-M geometry unless a separate replacement is recorded.

## Geometry changes

- Shell: extend the two hidden camera-end front-seat regions, clipped to the existing outer envelope and excluding the expanded camera plateau clearance. This reduces the corner pocket. It does not establish a globally undercut-free toolpath; residual blind clearance needs a shop-approved cutter or electrode approach.
- Frame: keep the outer outline, 1.80 mm overall thickness, four screw centers and 0.80 mm counterbore bearing floor. Enlarge the shallow inner relief from 72.55 x 150.71 to 72.85 x 151.01 mm and deepen it from 0.15 to 0.25 mm. The relief gains 0.15 mm per side and 0.10 mm depth.
- Liner: retain the phone-facing front surface at Z0.30. Extend its underside by 0.10 mm locally over the relieved frame land. The front flange is 0.40 mm there and 0.30 mm elsewhere; its nominal backing gap remains 0.15 mm. Rear pad 0.45 mm and nominal straight side walls 0.55 mm are unchanged.
- No global back or wall thickening, no new button caps, and no change to the outer camera mouth above Z12.18.

## Mass and exterior

The metal shell and frame total approximately 169.45 g in 304 stainless, or 57.19 g in 6061 aluminum, before hardware, liner and finishing. The 04-M2 metal set is about 0.25 g lighter than 04-M1: approximately +0.161 g in the shell and -0.414 g in the frame. Complete BRep volume differences and equal-resolution watertight mesh volumes agree on the change within 0.004 g. A coincident-surface Boolean difference estimate was discarded as numerically unreliable.

The nominal outer body footprint remains 76.45 x 156.41 mm; assembled body depth is 12.60 mm. Camera crown top is Z14.35 and maximum assembled depth is 16.15 mm. Twelve actual-CAD views were visually reviewed in `all-angle-review.png`.

## Verification completed

The final STEP files were checked with nine nominal geometry/source audits, an independent assembly review, and a combined-pose sensitivity study. All 11 check processes completed successfully. Core solids are valid; the exported core STL meshes are watertight. Nominal shell/frame/phone/liner intersections, modeled optical clearances, exposed buttons and Camera Control, bottom port access, screw-head support and frame approach were checked.

The assembly review includes 48 single-axis tilt/translation cases. A separate study samples 64 combined XYZ rotations of +/-0.1 degrees and translations of +/-0.20 mm. Those nominal rigid poses are non-overlapping. These are sampled sensitivity studies, not a proof that every real phone, liner or insertion path will fit.

### Unresolved fit hold point

The smallest rigid gap in the 64 combined cases is 0.069669 mm. Subtracting the unchanged provisional combined phone/case surface-error allowance of 0.10 mm leaves **-0.030331 mm**. This negative allowance is a release hold point, not a demonstrated physical collision. The assumed pose range has not been qualified against a specific liner's stiffness and compression. Production device variation and undimensioned camera/corner surfaces are also unqualified.

An actual bare iPhone 18 Pro fit check, qualified liner-constrained placement and agreed tolerances, or an agreed further internal geometry revision is required before claiming fit. The user's existing empty-part print alignment does not substitute for this check. No additional home prints are requested.

## Supplier response required

1. Shell: review the camera-end sections in the PDF and mark any remaining inaccessible face, required tool entry, electrode approach or minimum local dimension. Assess 5-axis/sinker-EDM or a suitable alternative without changing the selected exterior.
2. Frame: approve a supported process with controlled release. The attached carrier STEP is an optional sacrificial-stock study, not an additional delivered metal part. Every tab, center web and carrier edge must be removed. The DXF is a Z0 reference only; the finished STEP governs rounds, counterbores and relief.
3. Inspect the finished matched shell/frame after unclamping: proposed free-state mating flatness <=0.05 mm, seated joint gap <=0.05 mm, exterior edge step <=0.05 mm. Do not rely on screws to straighten a warped frame. These are requested acceptance limits, not supplier promises.
4. Retain the four centers X+/-33.10, Y+/-72.55 mm with proposed +/-0.02 mm XY coordinate limits on common datums. Confirm final bore sizes, M1.2 x 0.25 tapping, usable depth and supplied hardware. Intended screws: M1.2 x 0.25 x 3 mm DIN84A A2, head diameter 2.30 mm and height 0.80 mm. The smooth pilot CAD is not a modeled or inspected thread.
5. Route the liner to a flexible silicone/TPU/TPE specialist. Confirm grade, hardness, shrinkage, accuracy and retention. It is not a steel or rigid-resin CNC part. PCBWay's published standard vacuum-casting minimum is 0.75 mm, so that process cannot simply be assumed suitable for this 0.30-0.55 mm geometry. If needed, return a precise thin-molding or die-cut/laminated proposal for review.
6. Confirm actual bare-iPhone-18-Pro fit service explicitly. JLCCNC has declined it; PCBWay has not accepted it. Include installation/removal, soft-liner retention, actual screws, screen lip, all controls, USB-C plug access, speakers/microphones and camera/flash checks.
7. Quote 304 stainless fine as-machined and carefully deburred, with achievable Ra units/locations and proposed modeled edge breaks. No bead blasting or brushing. Owner polishing follows separately; bearing floors, threads, mating planes and thin camera lip need protection.
8. Itemize matched parts, liner/tooling, hardware, inspection, any phone fit service, shipping to 94102, lead time and failed-part/remake terms. Return the smallest local changes with dimensions and added finished mass if the exact candidate is not feasible.

JLCCNC has stated a 2 mm minimum at its marked locations and offers general ISO 2768 mK flatness, not the specific requested matched-part limits. PCBWay has flagged the prior shell pocket and thin frame/liner. Neither supplier has accepted 04-M2. This package authorizes no machining-risk acceptance, production or payment.

## Reference and limits

- Phone nominal body dimensions: [Apple iPhone 18 Pro dimensional drawing](https://developer.apple.com/download/files/accessories/dimensional-drawings/iphone-18-pro.pdf), September 9, 2026, 71.85 x 150.01 x 8.75 mm. Camera shoulder and some corner surfaces are drawing-scale estimates, not Apple production solid CAD.
- The preview uses Apple's aligned silver AR phone for visual context; its appearance is not a dimensional fit certification.
- [Original design reference](https://www.yankodesign.com/2026/06/01/this-grungy-metal-case-turns-your-iphone-17-pro-into-an-ipod-classic/), David Delahunty / Yanko Design. Illustrative finish is not a delivered surface sample.
- [PCBWay EDM process guide](https://www.pcbway.com/blog/CNC_Machining/Electrical_Discharge_Machining_EDM_Process_Types_Technical_Guide_3f35da5a.html) and [vacuum-casting capability](https://www.pcbway.com/rapid-prototyping/3D-Printing/3D-Printing-VC.html) informed process questions, not supplier acceptance of these parts.
- Continuous metal overlaps antenna keepouts and obstructs the wireless-charging path. Radio, satellite, NFC, thermal, drop, retention, polishing loss and protective performance remain untested. The user selected this construction with radio limitations.

The final PDF, three finished STEP files and manifest identify this exact candidate. Carrier geometry is process stock only. Engineering discussion remains open; this is not a production release.
